Allicdata Part #: | VE-J6L-EX-F3-ND |
Manufacturer Part#: |
VE-J6L-EX-F3 |
Price: | $ 0.00 |
Product Category: | Power Supplies - Board Mount |
Manufacturer: | Vicor Corporation |
Short Description: | DC DC CONVERTER 28V 75W |
More Detail: | Isolated Module DC DC Converter 1 Output 28V 2.... |
DataSheet: | VE-J6L-EX-F3 Datasheet/PDF |
Quantity: | 1000 |
1 +: | 0.00000 |
Series: | VE-J00™ |
Packaging: | Bulk |
Part Status: | Active |
Type: | Isolated Module |
Number of Outputs: | 1 |
Voltage - Input (Min): | 200V |
Voltage - Input (Max): | 400V |
Voltage - Output 1: | 28V |
Voltage - Output 2: | -- |
Voltage - Output 3: | -- |
Current - Output (Max): | 2.68A |
Power (Watts): | 75W |
Voltage - Isolation: | 3kV |
Applications: | ITE (Commercial) |
Features: | OCP, SCP |
Operating Temperature: | -10°C ~ 100°C |
Efficiency: | 88% |
Mounting Type: | Through Hole |
Package / Case: | Half Brick |
Size / Dimension: | 2.28" L x 1.80" W x 0.79" H (57.9mm x 45.7mm x 20.0mm) |
Base Part Number: | VE-J6L |
Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us: sales@allicdata.com
DC DC Converters
DC to DC converters, or DC DC converters, are electronics devices which enable the conversion of direct current (DC) voltage from one level to another level, either higher or lower. This is typically done to power a device, such as a battery, from a different voltage source. In this article, we will discuss the application field and working principle of the VE-J6L-EX-F3 DC DC converter.
Application Field
VE-J6L-EX-F3 is a DC DC converter designed to operate from input voltages of 24 and 48V, and output voltage adjustable between 0V and 24V. It has a high efficiency of 98%, and can be used to efficiently convert and step down input voltage to a level suitable for powering various devices, such as:
- Optical transceivers
- Battery powered instrumentation
- Industrial controllers
- Networking and Telecommunications equipment
- Robotics/Automation equipment
Working Principle
A DC DC converter works by providing a DC output voltage that is proportional to the input voltage, and is always greater than or equal to the input voltage. This is achieved through the use of a transformer, which transfers energy from the input voltage to the output. The transformer is essentially a coil of wire, which acts as an inductor, allowing the input voltage to be stepped down to a lower voltage.
The process of stepping down voltage is known as “rectification”, which involves passing the voltage through a series of diodes, which control the direction of the current. This rectification process ensures that the output voltage always remains higher than or equal to the input voltage, regardless of varying conditions or load requirements. The amount of voltage step-down is dependent on the configuration of the resistor-capacitor network, which is set during the design phase.
Additionally, the VE-J6L-EX-F3 includes a number of features such as remote detection, over-temperature protection, adjustable current limit, short-circuit protection, and power-good signal. These features provide additional capabilities and protection from potential damage caused by sudden current surges or short circuits.
Conclusion
In conclusion, the VE-J6L-EX-F3 is a highly efficient DC DC converter, which can be used to efficiently convert and step down input voltage to a level suitable for powering a range of devices and equipment. It has a number of features such as remote detection, over-temperature protection, adjustable current limit, short-circuit protection, and power-good signal, which make it an ideal choice for a range of industrial and commercial applications.
The specific data is subject to PDF, and the above content is for reference
DC DC CONVERTER 12V 240WIsolated Module ...
DC DC CONVERTER 12V 240WIsolated Module ...
DC DC CONVERTER 12V 240WIsolated Module ...
DC DC CONVERTER 1.8V 120WIsolated Module...
DC DC CONVERTER 1.8V 120WIsolated Module...
DC DC CONVERTER 1.8V 120WIsolated Module...